If you want to make Liquid LSD drops you would take the amount of crystal (eg. 10mg or 0.01g) then divide it by your desired dosage (I would recommend 50ug or 0.00005g per drop), and this will give you the amount of drops of solvent you will need to add to the bottle.
For example:
200 drops x 50ug crystal
=10mg Crystal
Take your dropper bottle, drop 200 drops of your solvent (75v ever-clear is an ideal choice) into the bottle, add 10mg of crystal to the liquid, and gently vortex the liquid in the bottle until all the crystal dissolves. Now you have 200 drops dosed at 50ug per drop.
50ug is good because you can control dosage more accurately. This is the dosage per drop that I would recommend.
If you are going to be making large batches of dropper bottles, you should note that each type and size of dropper is going to have a different volume of liquid per drop, so all your dropper bottles need to be the same or the dosages will be inaccurate. Again, you will need to take the dropper and count out 200 drops into a bottle. Then you can take a syringe and draw the liquid into the barrel to measure how much you will need per bottle. Now we do some more simple mathematics.
For example:
1 bottle = 200 drops = 25ml
20 bottles x 25ml = 500ml
1 bottle = 10mg Crystal
10mg x 20 bottles =200mg Crystal
NOTE: These are not actual numbers. You MUST measure drops from your own bottles, using your own solution. It will be different for everyone.
So now we take 500ml of our solvent, we weigh up 200mg of crystal, we add the crystal to the solvent and vortex until it is dissolved, then we measure out 25ml per bottle using our syringe, and now we have 20 bottles, each with 200 drops, dosed at 50ug per drop.
In terms of the solvent, LSD has a higher solubility in H20 than ethanol, so whatever ratio of ethanol:H2O you use, I would advise that it have at least 15% H2O as will allow the crystal to dissolve more easily, and do not go below 60% H2O, as the more water there is in the solution the more it will be prone to degradation. If you are going to make your own Ethanol:H2O solvent, make sure to use deionised water. Never use tap water, because the chlorine will destroy the LSD.
Your dropper bottle should be amber glass, as this prevents any harmful UV radiation getting to the LSD and degrading it into ISO-LSD which is neurologically inactive. Also, if you use ethanol or spiritus be aware that it will evaporate quite quickly if you leave the bottle open and therefore each drop would become a higher dosage, so dont leave the bottle open.
For example:
200 drops x 50ug crystal
=10mg Crystal
Take your dropper bottle, drop 200 drops of your solvent (75v ever-clear is an ideal choice) into the bottle, add 10mg of crystal to the liquid, and gently vortex the liquid in the bottle until all the crystal dissolves. Now you have 200 drops dosed at 50ug per drop.
50ug is good because you can control dosage more accurately. This is the dosage per drop that I would recommend.
If you are going to be making large batches of dropper bottles, you should note that each type and size of dropper is going to have a different volume of liquid per drop, so all your dropper bottles need to be the same or the dosages will be inaccurate. Again, you will need to take the dropper and count out 200 drops into a bottle. Then you can take a syringe and draw the liquid into the barrel to measure how much you will need per bottle. Now we do some more simple mathematics.
For example:
1 bottle = 200 drops = 25ml
20 bottles x 25ml = 500ml
1 bottle = 10mg Crystal
10mg x 20 bottles =200mg Crystal
NOTE: These are not actual numbers. You MUST measure drops from your own bottles, using your own solution. It will be different for everyone.
So now we take 500ml of our solvent, we weigh up 200mg of crystal, we add the crystal to the solvent and vortex until it is dissolved, then we measure out 25ml per bottle using our syringe, and now we have 20 bottles, each with 200 drops, dosed at 50ug per drop.
In terms of the solvent, LSD has a higher solubility in H20 than ethanol, so whatever ratio of ethanol:H2O you use, I would advise that it have at least 15% H2O as will allow the crystal to dissolve more easily, and do not go below 60% H2O, as the more water there is in the solution the more it will be prone to degradation. If you are going to make your own Ethanol:H2O solvent, make sure to use deionised water. Never use tap water, because the chlorine will destroy the LSD.
Your dropper bottle should be amber glass, as this prevents any harmful UV radiation getting to the LSD and degrading it into ISO-LSD which is neurologically inactive. Also, if you use ethanol or spiritus be aware that it will evaporate quite quickly if you leave the bottle open and therefore each drop would become a higher dosage, so dont leave the bottle open.